Electronics.

Ci-dessous un extrait traitant le sujet : Electronics.. Ce document contient 3077 mots. Pour le télécharger en entier, envoyez-nous un de vos documents grâce à notre système d’échange gratuit de ressources numériques ou achetez-le pour la modique somme d’un euro symbolique. Cette aide totalement rédigée en format pdf sera utile aux lycéens ou étudiants ayant un devoir à réaliser ou une leçon à approfondir en : Echange

---

Electronics.
I

INTRODUCTION

Electronics, field of engineering and applied physics dealing with the design and application of devices, usually electronic circuits, the operation of which depends on the
flow of electrons for the generation, transmission, reception, and storage of information. The information can consist of voice or music (audio signals) in a radio receiver,
a picture on a television screen, or numbers and other data in a computer.
Electronic circuits provide different functions to process this information, including amplification of weak signals to a usable level; generation of radio waves; extraction
of information, such as the recovery of an audio signal from a radio wave (demodulation); control, such as the superimposition of an audio signal onto radio waves
(modulation); and logic operations, such as the electronic processes taking place in computers.

II

HISTORICAL BACKGROUND

The introduction of vacuum tubes at the beginning of the 20th century was the starting point of the rapid growth of modern electronics. With vacuum tubes the
manipulation of signals became possible, which could not be done with the early telegraph and telephone circuit or with the early transmitters using high-voltage sparks
to create radio waves. For example, with vacuum tubes weak radio and audio signals could be amplified, and audio signals, such as music or voice, could be
superimposed on radio waves. The development of a large variety of tubes designed for specialized functions made possible the swift progress of radio communication
technology before World War II and the development of early computers during and shortly after the war.
The transistor, invented in 1948, has now almost completely replaced the vacuum tube in most of its applications. Incorporating an arrangement of semiconductor
materials and electrical contacts, the transistor provides the same functions as the vacuum tube but at reduced cost, weight, and power consumption and with higher
reliability. Subsequent advances in semiconductor technology, in part attributable to the intensity of research associated with the space-exploration effort, led to the
development of the integrated circuit. Integrated circuits may contain hundreds of thousands of transistors on a small piece of material and allow the construction of
complex electronic circuits, such as those in microcomputers, audio and video equipment, and communications satellites.

III

ELECTRONIC COMPONENTS

Electronic circuits consist of interconnections of electronic components. Components are classified into two categories--active or passive. Passive elements never supply
more energy than they absorb; active elements can supply more energy than they absorb. Passive components include resistors, capacitors, and inductors.
Components considered active include batteries, generators, vacuum tubes, and transistors.

A

Vacuum Tubes

A vacuum tube consists of an air-evacuated glass envelope that contains several metal electrodes. A simple, two-element tube (diode) consists of a cathode and an
anode that is connected to the positive terminal of a power supply. The cathode--a small metal tube heated by a filament--frees electrons , which migrate to the
anode--a metal cylinder around the cathode (also called the plate). If an alternating voltage is applied to the anode, electrons will only flow to the anode during the
positive half-cycle; during the negative cycle of the alternating voltage, the anode repels the electrons, and no current passes through the tube. Diodes connected in
such a way that only the positive half-cycles of an alternating current (AC) are permitted to pass are called rectifier tubes; these are used in the conversion of
alternating current to direct current (DC) (see Electricity; Rectification). By inserting a grid, consisting of a spiral of metal wire, between the cathode and the anode and
applying a negative voltage to the grid, the flow of electrons can be controlled. When the grid is negative, it repels electrons, and only a fraction of the electrons
emitted by the cathode can reach the anode. Such a tube, called a triode, can be used as an amplifier. Small variations in voltage at the grid, such as can be produced
by a radio or audio signal, will cause large variations in the flow of electrons from the cathode to the anode and, hence, in the circuitry connected to the anode.

B

Transistors

Transistors are made from semiconductors. These are materials, such as silicon or germanium, that are "doped" (have minute amounts of foreign elements added) so
that either an abundance or a lack of free electrons exists. In the former case, the semiconductor is called n-type, and in the latter case, p-type. By combining n-type
and p-type materials, a diode can be produced. When this diode is connected to a battery so that the p-type material is positive and the n-type negative, electrons are
repelled from the negative battery terminal and pass unimpeded to the p-region, which lacks electrons. With battery reversed, the electrons arriving in the p-material
can pass only with difficulty to the n-material, which is already filled with free electrons, and the current is almost zero.
The bipolar transistor was invented in 1948 as a replacement for the triode vacuum tube. It consists of three layers of doped material, forming two p-n (bipolar)
junctions with configurations of p-n-p or n-p-n. One junction is connected to a battery so as to allow current flow (forward bias), and the other junction has a battery
connected in the opposite direction (reverse bias). If the current in the forward-biased junction is varied by the addition of a signal, the current in the reverse-biased
junction of the transistor will vary accordingly. The principle can be used to construct amplifiers in which a small signal applied to the forward-biased junction causes a
large change in current in the reverse-biased junction.
Another type of transistor is the field-effect transistor (FET). Such a transistor operates on the principle of repulsion or attraction of charges due to a superimposed
electric field. Amplification of current is accomplished in a manner similar to the grid control of a vacuum tube. Field-effect transistors operate more efficiently than
bipolar types, because a large signal can be controlled by a very small amount of energy.

C

Integrated Circuits

Most integrated circuits are small pieces, or "chips," of silicon, perhaps 2 to 4 sq mm (0.08 to 0.15 sq in) long, in which transistors are fabricated. Photolithography
enables the designer to create tens of thousands of transistors on a single chip by proper placement of the many n-type and p-type regions. These are interconnected
with very small conducting paths during fabrication to produce complex special-purpose circuits. Such integrated circuits are called monolithic because they are
fabricated on a single crystal of silicon. Chips require much less space and power and are cheaper to manufacture than an equivalent circuit built by employing individual
transistors.

D

Resistors

If a battery is connected across a conducting material, a certain amount of current will flow through the material (see Resistance). This current is dependent on the
voltage of the battery, on the dimensions of the sample, and on the conductivity of the material itself. Resistors with known resistance are used for current control in

electronic circuits. The resistors are made from carbon mixtures, metal films, or resistance wire and have two connecting wires attached. Variable resistors, with an
adjustable sliding contact arm, are often used to control volume on radios and television sets.

E

Capacitors

Capacitors consist of two metal plates that are separated by an insulating material (see Capacitor). If a battery is connected to both plates, an electric charge will flow
for a short time and accumulate on each plate. If the battery is disconnected, the capacitor retains the charge and the voltage associated with it. Rapidly changing
voltages, such as caused by an audio or radio signal, produce larger current flows to and from the plates; the capacitor then functions as a conductor for the changing
current. This effect can be used, for example, to separate an audio or radio signal from a direct current in order to connect the output of one amplifier stage to the
input of the next amplifier stage.

F

Inductors

Inductors consist of a conducting wire wound into the form of a coil. When a current passes through the coil, a magnetic field is set up around it that tends to oppose
rapid changes in current intensity (see Induction). As a capacitor, an inductor can be used to distinguish between rapidly and slowly changing signals. When an inductor
is used in conjunction with a capacitor, the voltage in the inductor reaches a maximal value for a specific frequency. This principle is used in a radio receiver, where a
specific frequency is selected by a variable capacitor.

G

Sensing Devices and Transducers

Measurements of mechanical, thermal, electrical, and chemical quantities are made by devices called sensors and transducers. The sensor is responsive to changes in
the quantity to be measured, for example, temperature, position, or chemical concentration. The transducer converts such measurements into electrical signals, which,
usually amplified, can be fed to instruments for the readout, recording, or control of the measured quantities. Sensors and transducers can operate at locations remote
from the observer and in environments unsuitable or impractical for humans.
Some devices act as both sensor and transducer. A thermocouple has two junctions of wires of different metals; these generate a small electric voltage that depends on
the temperature difference between the two junctions. A thermistor is a special resistor, the resistance of which varies with temperature. A variable resistor can convert
mechanical movement into an electrical signal. Specially designed capacitors are used to measure distance, and photocells are used to detect light (see Photoelectric
Cell). Other devices are used to measure velocity, acceleration, or fluid flow. In most instances, the electric signal is weak and must be amplified by an electronic circuit.

IV

POWER-SUPPLY CIRCUITS

Most electronic equipment requires DC voltages for its operation. These can be provided by batteries (see Battery) or by internal power supplies that convert alternating
current as available at the home electric outlet, into regulated DC voltages. The first element in an internal DC power supply is a transformer, which steps up or steps
down the input voltage to a level suitable for the operation of the equipment. A secondary function of the transformer is to provide electrical ground insulation of the
device from the power line to reduce potential shock hazards. The transformer is then followed by a rectifier, normally a diode. In the past, vacuum diodes and a wide
variety of different materials such as germanium crystals or cadmium sulfide were employed in the low-power rectifiers used in electronic equipment. Today silicon
rectifiers are used almost exclusively because of their low cost and their high reliability.
Fluctuations and ripples superimposed on the rectified DC voltage (noticeable as a hum in a malfunctioning audio amplifier) can be filtered out by a capacitor; the larger
the capacitor, the smaller is the amount of ripple in the voltage. More precise control over voltage levels and ripples can be achieved by a voltage regulator, which also
makes the internal voltages independent of fluctuations that may be encountered at an outlet. A simple, often-used voltage regulator is the zener diode. It consists of a
solid-state p-n-junction diode, which acts as an insulator up to a predetermined voltage; above that voltage it becomes a conductor that bypasses excess voltages.
More sophisticated voltage regulators are usually constructed as integrated circuits.

V

AMPLIFIER CIRCUITS

Electronic amplifiers are used mainly to increase the voltage, current, or power of a signal. A linear amplifier provides signal amplification with little or no distortion, so
that the output is proportional to the input. A nonlinear amplifier may produce a considerable change in the waveform of the signal. Linear amplifiers are used for audio
and video signals, whereas nonlinear amplifiers find use in oscillators, power electronics, modulators, mixers, logic circuits, and other applications where an amplitude
cutoff is desired. Although vacuum tubes played a major role in amplifiers in the past, today either discrete transistor circuits or integrated circuits are mostly used.

A

Audio Amplifiers

Audio amplifiers, such as are found in radios, television sets, citizens band (CB) radios, and cassette recorders, are generally operated at frequencies below 20 kilohertz
(1 kHz = 1000 cycles/sec). They amplify the electrical signal, which then is converted to sound in a loudspeaker. Operational amplifiers (op-amps), built with integrated
circuits and consisting of DC-coupled, multistage, linear amplifiers are popular for audio amplifiers.

B

Video Amplifiers

Video amplifiers are used mainly for signals with a frequency spectrum range up to 6 megahertz (1 MHz = 1 million cycles/sec). The signal handled by the amplifier
becomes the visual information presented on the television screen, with the signal amplitude regulating the brightness of the spot forming the image on the screen. To
achieve its function, a video amplifier must operate over a wide band and amplify all frequencies equally and with low distortion. See Video Recording.

C

Radio Frequency Amplifiers

These amplifiers boost the signal level of radio or television communication systems. Their frequencies generally range from 100 kHz to 1 GHz (1 billion cycles/sec = 1
gigahertz) and can extend well into the microwave frequency range.

VI

OSCILLATORS

Oscillators generally consist of an amplifier and some type of feedback: The output signal is fed back to the input of the amplifier. The frequency-determining elements
may be a tuned inductance-capacitance circuit or a vibrating crystal. Crystal-controlled oscillators offer the highest precision and stability. Oscillators are used to

produce audio and radio signals for a wide variety of purposes. For example, simple audio-frequency oscillators are used in modern push-button telephones to transmit
data to the central telephone station for dialing. Audio tones generated by oscillators are also found in alarm clocks, radios, electronic organs, computers, and warning
systems. High-frequency oscillators are used in communications equipment to provide tuning and signal-detection functions. Radio and television stations use precise
high-frequency oscillators to produce transmitting frequencies.

VII

SWITCHING AND TIMING CIRCUITS

Switching and timing circuits, or logic circuits, form the heart of any device where signals must be selected or combined in a controlled manner. Applications of these
circuits include telephone switching, satellite transmissions, and digital computer operations.
Digital logic is a rational process for making simple "true" or "false" decisions based on the rules of Boolean algebra. "True" can be represented by a 1 and "false" by a 0,
and in logic circuits the numerals appear as signals of two different voltages. Logic circuits are used to make specific true-false decisions based on the presence of
multiple true-false signals at the inputs. The signals may be generated by mechanical switches or by solid-state transducers. Once the input signal has been accepted
and conditioned (to remove unwanted electrical signals, or "noise"), it is processed by the digital logic circuits. The various families of digital logic devices, usually
integrated circuits, perform a variety of logic functions through logic gates, including "OR,""AND," and "NOT," and combinations of these (such as "NOR," which includes
both OR and NOT). One widely used logic family is the transistor-transistor logic (TTL). Another family is the complementary metal oxide semiconductor logic (CMOS),
which performs similar functions at very low power levels but at slightly lower operating speeds. Several other, less popular families of logic circuits exist, including the
currently obsolete resistor-transistor logic (RTL) and the emitter coupled logic (ELC), the latter used for very-high-speed systems.
The elemental blocks in a logic device are called digital logic gates. An AND gate has two or more inputs and a single output. The output of an AND gate is true only if all
the inputs are true. An OR gate has two or more inputs and a single output. The output of an OR gate is true if any one of the inputs is true and is false if all of the
inputs are false. An INVERTER has a single input and a single output terminal and can change a true signal to a false signal, thus performing the NOT function. More
complicated logic circuits are built up from elementary gates. They include flip-flops (binary switches), counters, comparators, adders, and more complex combinations.
To perform a desired overall function, large numbers of logic elements may be connected in complex circuits. In some cases microprocessors are utilized to perform
many of the switching and timing functions of the individual logic elements (see Microprocessor). The processors are specifically programmed with individual instructions
to perform a given task or tasks. An advantage of microprocessors is that they make possible the performance of different logic functions, depending on the program
instructions that are stored. A disadvantage of microprocessors is that normally they operate in a sequential mode, which may be too slow for some applications. In
these cases specifically designed logic circuits are used.

VIII

RECENT DEVELOPMENTS

The development of integrated circuits has revolutionized the fields of communications, information handling, and computing. Integrated circuits reduce the size of
devices and lower manufacturing and system costs, while at the same time providing high speed and increased reliability. Digital watches, hand-held computers, and
electronic games are systems based on microprocessors. Other developments include the digitalization of audio signals, where the frequency and amplitude of an audio
signal are coded digitally by appropriate sampling techniques, that is, techniques for measuring the amplitude of the signal at very short intervals. Digitally recorded
music shows a fidelity that is not possible using direct-recording methods. Digital playback devices of this nature have already entered the home market. Digital storage
could also form the basis of home video systems and may significantly alter library storage systems, because much more information can be stored on a disk for replay
on a television screen than can be contained in a book.
Medical electronics has progressed from computerized axial tomography, or the use of CAT or CT scanners (see X Ray), to systems that can discriminate more and more
of the organs of the human body. Devices that can view blood vessels and the respiratory system have been developed as well. Ultrahigh definition television also
promises to substitute for many photographic processes, because it eliminates the need for silver.
Today's research to increase the speed and capacity of computers concentrates mainly on the improvement of integrated circuit technology and the development of
even faster switching components. Very-large-scale integrated (VLSI) circuits that contain several hundred thousand components on a single chip have been developed.
Very-high-speed computers are being developed in which semiconductors may be replaced by superconducting circuits using Josephson junctions (see Josephson
Effect) and operating at temperatures near absolute zero.

Contributed By:
Fred Landis
George R. Steber
Steven E. Reyer
Microsoft ® Encarta ® 2009. © 1993-2008 Microsoft Corporation. All rights reserved.